300-075 | All About Download 300-075 exam dumps

New Questions 11

Which action configures transcoding resources in Cisco Unified Communications Manager to function with branch office Cisco IP Phones?

A. Configure the branch office IP phones with CSS and partitions.

B. Configure the branch office IP phones with MRGs and MRGLs.

C. Configure the branch office IP phones with regions.

D. Configure the branch office IP phones with locations.

Answer: B

New Questions 12

An engineer is configuring URI calling within the same cluster. Which four actions must be taken to accomplish this configuration? (Choose four.)

A. Configure SIP route patterns.

B. Configure the directory URI partition and calling search space.

C. Associate the directory URIs to directory numbers.

D. Activate the URI service in Cisco Unified Serviceability.

E. Configure SIP trunk.

F. Assign directory URIs to users.

G. Configure the SIP profile.

H. Configure the URI service parameters.

Answer: B,C,F,H

New Questions 13

Which command can be used to manually send the MGCP gateway to register with the

secondary Cisco Unified Communications Manager server?

A. ccm-manager switchover-to-backup

B. mgcp use backup

C. ccm-manager register backup

D. not supported

Answer: A

New Questions 14

On which Cisco Unified Communications Manager configuration parameter does the CODEC that a Cisco IP Phone uses for a call depend?

A. enterprise parameters

B. media resources

C. physical location

D. region

E. location

Answer: D

New Questions 15

You need to verify if the Media Control Gateway Protocol gateway is enabled and active. Which command should you use for this purpose?

A. show running-config

B. show fallback-mgcp

C. show gateway

D. show ccm-manager fallback-mgcp

E. show running-config gateway

F. show fallback-mgcp ccm-manager

Answer: D

New Questions 16

Which action configures AAR to route the calls that have been rejected by the gatekeeper CAC through the PSTN?

A. Configure Cisco IP Phones for AAR.

B. Configure AAR to work with SRST.

C. Configure AAR to work with CTI route points.

D. This configuration is not possible using AAR.

Answer: D

New Questions 17

Refer to the exhibit.

The exhibit shows centralized Cisco Unified Communications Manager configuration components for TEHO calls to U.S. area code 408 from the U.K. The PSTN access code for the U.K. is 9 and 001 for international calls to the U.S. Assuming the PSTN does not accept globalized numbers with + prefix. What should the Called Party Transformation Pattern at the U.S. gateway be configured as?

A. +.! with the following Called Party Transformation: Discard Digits PreDot

Prefix Digits Outgoing Calls: +

B. +1.! with the following Called Party Transformation: Discard Digits PreDot

Prefix Digits Outgoing Calls: None

C. +408.! with the following Called Party Transformation: Discard Digits PreDot

Prefix Digits Outgoing Calls: 1

D. +1408.! with the following Called Party Transformation: Discard Digits PreDot

Prefix Digits Outgoing Calls: None

E. +1.408! with the following Called Party Transformation: Discard Digits PreDot

Prefix Digits Outgoing Calls: None

Answer: D

New Questions 18

To preserve analog calls in an MGCP switchback event, which three commands must be configured in the MGCP fallback router? (Choose three.)

A. h323

B. mgcp-switchback-graceful

C. voice service voip

D. mgcp-graceful

E. preserve-h323

F. no h225 timeout keepalive

Answer: A,C,F

Explanation: Incorrect: BDE

these additional command for call preservation when using MGCP fallback: voice service voip

h323

no h225 timeout keepalive

ReferencE. CCNP Voice CIPT2 642-457 Quick Reference, 2nd Edition

New Questions 19

How many hosted DN patterns per cluster does Cisco Unified Communications Manager allow you to configure?

A. 500

B. 1000

C. 1500

D. 2000

E. 2500

F. 5000

Answer: D

New Questions 20

Which statement is true when device mobility mode is enabled or disabled in the Phone Configuration window?

A. The device mobility mode phone settings take precedence over the service parameter settings.

B. The service parameter settings take precedence over the device mobility mode phone settings.

C. The combined service parameter settings and the device mobility mode phone settings will be used.

D. The default settings will be used due to the conflicts.

Answer: A